Masimo Radical Signal Extraction Betreibershandbuch PDF herunterladen (Seite 38)

3-6 Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual

SATSHARE SETUP (CONTINUED)

7. While in the SatShare mode, if there are any significant discrepancies between the

readings from the Radical-7 Pulse CO-Oximeter and those on the monitor displaying

the values obtained from SatShare, the values reported by the Radical-7 Pulse

CO-Oximeter are to be considered the correct values.

8. To use the Radical-7 Pulse CO-Oximeter with SatShare while it is not connected to

AC power, set the Power Save parameter in the General menu to “No” and refer to

Section 4, Operation. Please note that if the Radical-7 Pulse CO-Oximeter is used in

this mode, the length of time the Radical-7 Pulse CO-Oximeter can operate on battery

power will be significantly diminished.

9. Set the SatShare Numbers and the Interface Alarms SpO

/pulse rate parameters in

the General menu according to customer preference.

When Rainbow parameters (SpCO, SpMet, SpHb, etc.) are configured, Interface

Alarms "SpO

/BPM" can be set to “Yes” or “No”. The “Yes” setting allows SpO

and

pulse rate audible alarms at both the Radical-7 and the interfaced system. The “No”

setting mutes the SpO

and pulse rate audible alarms at the Radical-7 while allowing

SpO

and pulse rate audible alarm alerts at the interfaced system. The “No” setting

prevents both systems (Radical-7 and interfaced system) from producing audible

alarms at the same time. See section 4: General.

NOTE: The Radical-7 reverts to Interface Alarm "SpO

/BPM" “Yes” during power

interruptions or when the SatShare connection is lost or the instrument becomes

separated from the docking station. This ensures that the Radical-7 provides audible

alarms for SpO

and pulse rate when the connection to the interfaced system

becomes compromised.

10. If displaying the simulated waveform is not desirable, it is recommended to turn off the

plethysmographic waveform display of the multiparameter patient monitor.

 SATSHARE SIGNALS ARE IDEAL SIMULATED WAVEFORMS CORRESPONDING TO

THE CALCULATED SATURATION AND PULSE RATE VALUES AND DO NOT CONTAIN

ALL OF THE INFORMATION CONTAINED IN PHYSIOLOGICAL WAVEFORMS. THE

MULTIPARAMETER PATIENT MONITOR TRANSLATES THESE SIGNALS INTO

SATURATION AND PULSE RATE VALUES.

 DURING SATSHARE OPERATION, THE AUDIBLE ALARMS MAY BE MUTED ON

THE RADICAL-7 PULSE CO-OXIMETER. WHEN THE AUDIBLE ALARM IS MUTED

(INDICATED BY THE BELL WITH A SLASH THROUGH IT) ON THE RADICAL-7

PULSE CO-OXIMETER, USE THE MULTIPARAMETER MONITOR FOR AUDIBLE

ALARM INDICATION.

 DURING SATSHARE OPERATION DO NOT USE THE PLETHYSMOGRAPHIC

WAVEFORM DISPLAY ON THE MULTIPARAMETER MONITOR FOR DIAGNOSTIC

PURPOSES. INSTEAD, USE THE PLETHYSMOGRAPHIC WAVEFORM DISPLAYED

ON THE RADICAL-7 PULSE CO-OXIMETER SCREEN.

 TO AVOID EXCESSIVE BATTERY DISCHARGING, DO NOT CONNECT ANY

EQUIPMENT TO THE SATSHARE CONNECTOR UNLESS THE RADICAL-7 PULSE

CO-OXIMETER IS CONNECTED TO THE AC MAINS POWER SUPPLY.

 ONLY USE A SATSHARE CABLE THAT HAS A FERRITE BEAD INSTALLED.

 ONLY SpO

AND PULSE RATE CAN BE DISPLAYED ON THE MULTIPARAMETER

MONITOR WITH SATSHARE.

Setup

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 115 116

Kommentare zu diesen Handbüchern

Keine Kommentare

Masimo Radical Signal Extraction Betreibershandbuch Seite 38

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messen, Testen & Steuern Masimo Radical Signal Extraction